This is an old revision of the document!
UniFi AP AC Pro
Series Type: UniFi
Website Link: AP AC Pro
Model: UAP‑AC‑PRO
Type: 802.11ac PRO Access Point
Description: The UniFi AC Pro AP features the latest Wi-Fi 802.11ac, 3x3 MIMO technology in a refined industrial design and is ideal for deployment of maximum‑performance wireless networks.
Specifications
| UAP‑AC‑PRO | |
|---|---|
| Dimensions | 196.7 x 196.7 x 35 mm (7.74 x 7.74 x 1.38") |
| Weight | 350 g (12.4 oz) |
| With Mounting Kits | 450 g (15.9 oz) |
| Networking Interface | (1) 10/100/1000 Ethernet Port |
| Port | (1) USB 2.0 Port |
| Buttons | Reset |
| Power Method - Option 1 | 802.3af/802.3at Supported |
| Power Method - Option 2 | Passive Power over Ethernet (48V), (Supported Voltage Range: 44 to 57VDC) |
| Power Supply | 48V, 0.5A PoE Gigabit Adapter (* Only the single-pack of the UAP-AC-PRO includes a PoE adapter.) |
| Power Save | Supported |
| Maximum Power Consumption | 9W |
| Maximum TX Power | |
| 2.4 GHz | 22 dBm |
| 5 GHz | 22 dBm |
| Antennas | (3) Dual-Band Antennas, 2.4 GHz: 3 dBi, 5 GHz: 3 dBi |
| Wi-Fi Standards | 802.11 a/b/g/n/ac |
| Wireless Security | WEP, WPA-PSK, WPA-Enterprise (WPA/WPA2, TKIP/AES) |
| BSSID | Up to 8 per Radio |
| Mounting | Wall/Ceiling (Kits Included) |
| Operating Temperature | -10 to 70° C (14 to 158° F) |
| Operating Humidity | 5 to 95% Noncondensing |
| Certifications | CE, FCC, IC |
| Hardware | |
|---|---|
| Instruction set | MIPS |
| Vendor | Qualcomm / Atheros |
| Bootloader | UBoot |
| System-On-Chip | QCA9563-AL3A |
| CPU Frq | 775 MHz |
| BogoMIPS | 385.84 |
| Flash-Chip | Macronix MX25L12835FMI |
| Flash size | 16 MiB |
| RAM-Chip | Winbond W971GG6KB-25 |
| RAM size | 128 MiB |
| Wireless 1 (2.4 GHz) | QCA9563 built-in |
| Wireless 2 (5 GHz) | QCA9880-BR4A |
| Eth Phy | QCA8334-AL3C |
| USB | USB 2.0 |
| Serial | Yes, for U-Boot |
| Advanced Traffic Management | |
|---|---|
| VLAN | 802.1Q |
| Advanced QoS | Per-User Rate Limiting |
| Guest Traffic Isolation | Supported |
| WMM | Voice, Video, Best Effort, and Background |
| Concurrent Clients | 250+ |
| Supported Data Rates (Mbps) | |
|---|---|
| Standard | Data Rates |
| 802.11ac | 6.5 Mbps to 1300 Mbps (MCS0 - MCS9 NSS1/2/3, VHT 20/40/80) |
| 802.11n | 6.5 Mbps to 450 Mbps (MCS0 - MCS23, HT 20/40) |
| 802.11a | 6, 9, 12, 18, 24, 36, 48, 54 Mbps |
| 802.11g | 6, 9, 12, 18, 24, 36, 48, 54 Mbps |
| 802.11b | 1, 2, 5.5, 11 Mbps |
LED Status Light Ring
- Blue Ring - Solid
- Normal Operation
- White Ring - Flashing
- Unconfigured state
Troubleshooting tips
- No light/power
- Check ethernet connection.
- Are you connected to a PoE enabled switch or PoE injector?
- Does the switch/injector have power?
- Can only connect to the primary/default VLAN
- Check that your switch port has all VLANs enabled (Try cycling the port through 'Disabled')
FAQ
- How do I perform a factory reset?
- Hold the reset button for 5-10sec.
- This will reset the AP and require a controller to re-adopt the unit. This is not recomended for general troubleshooting!
- How many networks can I run off of this one AP?
- Up to 8 per Radio
- Does this AP come with a PoE injector for use on a non-PoE enabled switch?
- Yes!
NOTE: The 5pack version of this AP does NOT come with PoE injector, it is recommended to use them with a PoE enabled switch like the UniFi Switch 8-150W or better.