Series Type: UniFi Mesh
Website Link: AC Mesh
Model: UAP-AC-M
Type: 802.11AC Indoor/Outdoor Wi-Fi Access Points with Plug & Play Mesh Technology

Description: The UAP-AC-M provides simultaneous, dual-band, 2x2 MIMO technology.

UAP-AC-LITE
Dimensions 353 x 46 x 34.4 mm (13.9 x 1.81 x 1.35")
Weight 152 g (5.36 oz)
Networking Interface (1) 10/100/1000 Ethernet Port
Buttons Reset
Power Method - Option 1 802.3af/A PoE
Power Method - Option 2 24V Passive PoE (Pairs 4, 5+; 7, 8 Return)
Power Supply 24V, 0.5A Gigabit PoE Adapter (* Only the single-pack of the UAP-AC-LITE includes a PoE adapter.)
Power Save Supported
Maximum Power Consumption 8.5W
Maximum TX Power
2.4 GHz 20 dBm
5 GHz 20 dBm
Antennas (2) Dual-Band Antennas, 2.4: 3dBi, 5.8: 4dBi
Wi-Fi Standards 802.11 a/b/g/n/ac
Wireless Security WEP, WPA-PSK, WPA-Enterprise (WPA/WPA2, TKIP/AES)
BSSID Up to 8 per Radio
Mounting Wall/Ceiling (Kits Included)
Operating Temperature -30 to 70° C (-22 to 158° F)
Operating Humidity 5 to 95% Noncondensing
Certifications CE, FCC, IC


Hardware
Instruction set MIPS
Vendor Qualcomm / Atheros
Bootloader UBoot
System-On-Chip QCA9563-AL3A
CPU Frq 775 MHz
BogoMIPS 385.84
Flash-Chip Macronix MX25L12835FMI
Flash size 16 MiB
RAM-Chip Winbond W971GG6KB-25
RAM size 128 MiB
Wireless 1 (2.4 GHz) QCA9563 built-in
Wireless 2 (5 GHz) Ubiquiti U-AME-G1-BR4A (custom QCA988X)
Eth Phy Atheros AR8033-AL1A
USB possibly unpopulated
Serial Yes, for U-Boot


Advanced Traffic Management
VLAN 802.1Q
Advanced QoS Per-User Rate Limiting
Guest Traffic Isolation Supported
WMM Voice, Video, Best Effort, and Background
Concurrent Clients 250+


Supported Data Rates (Mbps)
Standard Data Rates
802.11ac 6.5 Mbps to 867 Mbps (MCS0 - MCS9 NSS1/2, VHT 20/40/80)
802.11n 6.5 Mbps to 300 Mbps (MCS0 - MCS15, HT 20/40)
802.11a 6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11g 6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11b 1, 2, 5.5, 11 Mbps
  1. Blue Ring - Solid
    1. Normal Operation
  2. White Ring - Flashing
    1. Unconfigured state
  1. No light/power
    1. Check ethernet connection.
    2. Are you connected to a PoE enabled switch or PoE injector?
    3. Does the switch/injector have power?
  2. Can only connect to the primary/default VLAN
    1. Check that your switch port has all VLANs enabled (Try cycling the port through 'Disabled')
  • How do I perform a factory reset?
    • Hold the reset button for 5-10sec.
    • This will reset the AP and require a controller to re-adopt the unit. This is not recomended for general troubleshooting!
  • How many networks can I run off of this one AP?
    • Up to 8 per Radio
  • Does this AP come with a PoE injector for use on a non-PoE enabled switch?
    • ??
  • products/unifi/unifi_mesh.txt
  • Last modified: 2018/06/13 14:36
  • by nevyn